Ilmoituksen Uudet Hazemag 1000x930 telamurskain kohde on myyty, eikä se sisälly hakuun!
Samankaltaiset ilmoitukset
Verdés 128+ telamurskain Verdés 128+ 65 000 € Telamurskain 2006 Portugali, Ramalhal
uudet Hazemag 1000x930 telamurskain
Myyty
uudet Hazemag 1000x930 telamurskain
uudet Hazemag 1000x930 telamurskain kuva 2
uudet Hazemag 1000x930 telamurskain kuva 3
uudet Hazemag 1000x930 telamurskain kuva 4
uudet Hazemag 1000x930 telamurskain kuva 5
uudet Hazemag 1000x930 telamurskain kuva 6
uudet Hazemag 1000x930 telamurskain kuva 7
uudet Hazemag 1000x930 telamurskain kuva 8
uudet Hazemag 1000x930 telamurskain kuva 9
uudet Hazemag 1000x930 telamurskain kuva 10
uudet Hazemag 1000x930 telamurskain kuva 11
uudet Hazemag 1000x930 telamurskain kuva 12
uudet Hazemag 1000x930 telamurskain kuva 13
1/13
Merkki:  Hazemag
Malli:  1000x930
Tyyppi:  telamurskain
Sijainti:  Slovakia Horovce7705 km sijainnistasi
Julkaistu:  yli 1 kuukausi
Machineryline ID:  FW40023
Kuvaus
Säiliön tilavuus:  2,832 m³
Kapasiteetti:  30 t/h
Kunto
Kunto:  uusi
Lisätietoja
Väri:  vihreä

Lisätietoja — Uudet Hazemag 1000x930 telamurskain

Never used machine.
Feed capacity: approx. 35 t/h

Grain size: Raw material: 0-150 μm Circulation material: 0-150 mm Bulk density: 1.0-1.2 g/cm2
Free moisture: 0-0.5%
Temperature: 120 °C
Product: Briquette > 10 mm 25 t/h fine < 10 mm approx. 10 t/h


Device parameters: Roll diameter:

1000 mm

Roll body width: 930 mm
Maximum load: 7200 kN
Rolling speed: 0.42 m/s
Press: 400 kW Hydraulic system: 3 kW

Roller presses are used for pressing or briquetting various types of coal, minerals, ores and mixtures with binders. In order to achieve sufficient breaking strength by pressing or briquetting, products with low surface moisture are suitable for handling. Depending on the input material and the final product, roller presses can be equipped with optional functions. The material fed into the screw is a mixture of gypsum hemihydrate and gypsum dihydrate. The arrow screw lifts the material and pushes it into the area between the two rollers. Briquettes are created by pressing the material in the gap between the cylinders. A certain part of the material leaves the press through the gaps of the trough forms. The subsequent screening process is performed with a 10 mm cut. Adapting the press to the overall system as part of the trial run is extremely important to deliver a product that meets quality requirements. Interruption of the briquetting process due to a lack of material leads to disruption of the material flow as well as excessive stress on the roller press. The technical description of control and regulation of the roller press, including accessories, is part of the specification of the independent energy and control system supplier.